Electrical Calculators
The tools most needed in electrical installation and design are collected on this page: cable size and voltage drop, motor current with fuse and contactor selection, power factor correction, short-circuit current, transformer and generator sizing, solar system sizing, energy use, Ohm's law, resistor colour code, AWG and analog signal scaling.
Each tool explains a worked example, its assumptions and common mistakes. Calculations run in your browser; your data is not sent to a server.
Tools
kW – kVA – Amps Converter
Converts between kW, kVA and amps for single-phase, three-phase and DC.
Open ToolCable Size & Voltage Drop Calculator
Finds the cable size and % voltage drop from power/current and length.
Open ToolCable Current-Carrying Capacity Table
Cu/Al cable current-carrying capacity table; finds the smallest size for a current.
Open ToolCircuit Breaker (MCB) Sizing
Picks a standard MCB rating from load current and checks the cable match.
Open ToolMotor Current, Fuse & Contactor Selection
Finds rated current, fuse, contactor and thermal relay values from motor power.
Open ToolPower Factor Correction Calculator
Finds the required capacitor kVAr and checks monthly reactive ratios.
Open ToolShort-Circuit Current Calculator
Calculates three-phase fault current (kA) at the transformer and cable end.
Open ToolTransformer & Generator Sizing Calculator
Finds total kVA and the transformer and generator rating from a load list.
Open ToolUPS / Battery Runtime Calculator
Calculates UPS runtime from battery capacity and load, and the Ah needed for a target time.
Open ToolLighting Calculator (Lumen Method)
Calculates the number of luminaires, layout and total power by the lumen method.
Open ToolSolar Panel Calculator
Preliminary panel count, kWp, yearly output and area from consumption.
Open ToolElectricity Consumption & Cost Calculator
Calculates monthly electricity use (kWh) and cost of appliances.
Open ToolResistor Color Code Calculator
Finds resistance and tolerance from colour bands (4/5 band).
Open ToolAnalog Signal Scaling (4-20 mA, 0-10 V)
Scales 4-20 mA / 0-10 V signals and gives the PLC raw value and SCL code.
Open ToolEngineering Unit Converter
Converts pressure, power, energy, flow, torque and other engineering units.
Open ToolWhich tool for which job?
- I want to convert between kilowatts, kVA and amps → kW – kVA – Amps Converter
- I want to see cable current-carrying capacity by size in a table → Cable Current-Carrying Capacity Table
- I want to pick a circuit breaker from the load current → Circuit Breaker (MCB) Sizing
- I want to calculate how long a UPS battery will last → UPS / Battery Runtime Calculator
- I want to calculate how many luminaires a room needs → Lighting Calculator (Lumen Method)
- I want to check the cable size and voltage drop for a load → Cable Size & Voltage Drop Calculator
- I want fuse, contactor and thermal settings for a motor → Motor Current, Fuse & Contactor Selection
- I need the kVAr for reactive-power penalties or a correction panel → Power Factor Correction Calculator
- I want to check short-circuit current at a point after the transformer → Short-Circuit Current Calculator
- I want to size a transformer or generator from the total load → Transformer & Generator Sizing Calculator
- I want to see how many panels a solar system needs from monthly use → Solar Panel Calculator
- I want to calculate device energy use and cost → Electricity Consumption & Cost Calculator
- I want a quick calculation between voltage, current, resistance and power → Ohm's Law Calculator
- I want to read a resistor's value from its colour bands → Resistor Color Code Calculator
- I want to match AWG with mm² → AWG to mm² Converter
- I want to convert a 4-20 mA or 0-10 V signal to engineering units in a PLC → Analog Signal Scaling (4-20 mA, 0-10 V)
- I want unit conversions such as HP-kW or bar-psi → Engineering Unit Converter
Scope of the calculations
The tools are for preliminary sizing and checking. In a real installation, installation method, temperature, harmonics, protection coordination and the relevant standards need separate assessment. The final decision rests with a qualified engineer.
Design and quotation
For solar, power factor correction and electrical contracting work, you can send a request through the quote page if you want site-specific calculations and an offer.
Frequently asked questions
Do these tools replace a design?
No. They are for preliminary design and checking; approval and construction need standards, manufacturer data and a qualified engineer's assessment.
Where are calculations done?
In your browser. The values you enter are not sent to a server.
Which tool should I use first?
When sizing an installation, usually start from the load list (transformer/generator), then motor and cable selection, and finish with power factor and short-circuit checks.